Embedded Design & Automation Technology- Brighten your career

SME provides different solution to industry as well as R&D sectors. SME provides students a platform where student learn industrial system with advance embedded technology with design & development. Details of Training are given below.

Embedded Design Technology:   

full course duration: 4 weeks, 6 weeks, 3 month, 6 month

 Register here

  • Basic Embedded Design Technology

This Course includes Interfacing of all basic components (given below) with AVR Series Microcontroller (ATmega8/ ATmega16/ Amega32) or with Arduino. It includes sound knowledge about input output, pull & push registers, PORTs, PINs, DDRs, Pull & Push registers with practically implementation on Zero size PCB. Participators will design interfacing board themselves to work at our lab. 

Basic Embedded Technology includes: 

  • Light Emitting Diode (LED
  • Liquid Crystal Display (16×2 LCD)
  • DC Motor (L293D Driver IC)
  • Seven Segment (Common Cathode/ Common Anode)
  • Switch (DPDT/ DPST/ Sliding Switch)
  • DC Relay
  • Regulator/Diode/Capacitor
  • Transistor (NPN/ PNP)
  • Power Supply (5V/ 12V)

 Eligibility Criteria:

Participant must have knowledge about Turbo ‘C’. Knowledge about resistors, transistors, relay, power supply, would make advantages.

Course fee: – For AVR MCU- 6500/-. For Arduino- 8500/-, For ARM- 12,500/-,

Course Duration: 4 Weeks

 Register here


  • Sensor Embedded Design Technology

This course includes Interfacing of Sensors (Digital/ Analog) with ATMEL AVR Series Microcontroller (ATmega8/ ATmega16/ ATmega32) or Arduino with 16×2 LCD. It includes sound knowledge about ADC, Digital, converters, input output, pull & push registers with practically implementation.


Course module Includes:

  • Infrared (IR) Sensor  Module
  • Temperature  Sensor (LM34/LM35) Module
  • Bump Sensor Module
  • Potentiometer Module
  • Pyroelectric Infrared (PIR) Motion Sensor Module
  • Sound Sensor Module
  • Metal Detecting Sensor Module
  • Liquefied Petroleum Gas (LPG) Sensor / Fire Sensor Module
  • Alcohol Gas Sensor Module
  • Dimmer Module
  • Accelerometer (3 axis/ 2 axis) /Tilt sensor Module
  • *FSR
  • *Finger Print Sensor
  • *Bar Coder Reader
  • *Soil Moisture Sensor


Eligibility Criteria:   

Applicant must have sound knowledge of Basic Embedded Technology, PORTS, PINS, Registers, Interfacing of 16*2 & 20*4 LCD with Microcontrollers, LEDs, Relay, 7Seg, Transistor etc

Course fee: – For AVR 8500/-, For Arduino 10,500/-,   For ARM 16,500/-,

Course Duration: 2-4 Weeks

 Register here


  • Wireless Embedded Design Technology


This training course includes basic of (UART/USART), SPI, & I2C Communication, different operating levels, level converters & interfacing them with AVR Series Microcontroller(ATmega8/ ATmega16/ ATmega32) or with Arduino. Participators will design interfacing board themselves to work at our lab.

Wireless Embedded System Includes: 

  • Two Wire Interface (MCU to MCU) between two Microcontroller
  • Communication between PC & Microcontroller using Terminal v1.9b 
  • Rivest Cipher version 5 (RC5) Protocol Module
  • Global Service for Mobile (GSM) Module 
  • RF (433 MHz) Wireless Module   
  • Radio Frequency Identification (RFID) Module 
  • National Electric Code (NEC) Protocol Module 
  • 15.4 IEEE standard Protocol based Wireless transceiver (Zigbee) Module 
  • Power Line Carrier Communication (PLCC) Module
  • Duel Tone Multiple Frequency (DTMF) Module


Eligibility Criteria: 

Applicant must have sound knowledge about Register, Ports, Pins, Digital Input & Output, Vcc, GND, Switching.

Course fee: – for AVR- 10,500/-, For Arduino- 12,500/-, For ARM- 20,500/-

Course Duration: 2-4 Weeks

 Register here


  • Advance Embedded Design Technology

Advance Embedded System include Complete Description of Inter Integrated Circuit (I2C), SPI (Serial Peripheral Interface) Protocols, Timer / Counter, Interrupt programming, Introduction of Real time Operating system (RTOS)/ Counter with AVR Series Microcontroller (ATmega8/ ATmega16/ ATmega32). These are real time industrial application system, industry already develop product using these systems. Certificate will be provided after completion of the course.

Training module Includes:

  • Timer
  • I2C (Inter Integrated Circuit ) / Two Wire Interface (TWI)
  • Interrupt (Internal & External)
  • SPI (Serial Peripheral Interface)
  • ASIC (Application Specific Integrated Circuit)
  • Introduction to Real Time Operating System(RTOS )/ Counter
  • PORT Programming


Course fee:  20,000/-.

Eligibility Criteria: This course is only for those participators, who has sound knowledge on BasicSensor & Wireless Embedded Technolgoy with All registers, Inputs, Outputs Interfacing, pull push registers, serial data fetching with ADC & DAC etc.

Course Duration: 4 Weeks

 Register here